抗冲ACR树脂的合成及其性能评价

采用种子乳液聚合法,以丙烯酸丁酯为核层单体、甲基丙烯酸甲酯为壳层单体、甲基丙烯酸烯丙酯为交联剂制备了抗冲ACR树脂。考察了不同加料方式对ACR乳液粒径及对PVC冲击性能的影响,结果表明:连续滴加方式可实现乳液粒径的稳定控制,并能得到性能优异的抗冲ACR树脂。     

控锻控冷工艺对GCr15轴承钢力学性能的影响

探究不同控锻控冷热处理工艺对GCr15钢力学性能的影响,测试了它的回火稳定性、冲击性能、滚动接触疲劳寿命。结果表明,采用控锻控冷工艺可提高试样的抗回火稳定性,冲击性能提高50%以上,接触疲劳寿命提高40%以上。     

多因素影响下苯乙烯-丁二烯-苯乙烯嵌段共聚物改性沥青性能分析

通过掺加不同含量糠醛抽出油、红油增塑剂与苯乙烯-丁二烯-苯乙烯嵌段共聚物(SBS)改性剂,分析其对SBS改性沥青各性能指标的影响,判断影响SBS改性沥青性能的主要因素。结果表明:改性沥青中SBS改性剂含量是提高软化点、弹性恢复的主要因素;糠醛抽出油含量增大则可明显提高其延度指标,且改善SBS改性沥青的离析程度;红油增塑剂含量增大可大幅提高SBS改性沥青的延度指标,但高温性能下降且离析严重,短期老化后指标下降幅度高于同等含量抽出油老化后指标。因此可在SBS含量确定的情况下,通过掺加适当的糠醛抽出油以改善SBS改性沥青的性能。     

基于功频下垂控制的光伏并网发电系统惯量阻尼机理研究

针对光伏以低惯量、弱阻尼的特征大规模接入电网，给电网稳定性带来不利影响的问题，基于功频下垂控制的光伏并网发电系统，借鉴经典电气转矩分析法，从物理机制层面上分析影响系统惯量、阻尼以及同步能力的作用规律。研究结果表明对于控制参数的影响规律而言，惯量特性主要受功率环的比例系数Kp影响，且随Kp的增大而增强；阻尼特性受频率下垂系数Dp影响比较明显，且随Dp的增大而减弱；同步特性只受功率环的比例积分系数Ki影响，且随Ki的增大而增强。通过仿真验证了理论分析的正确性。     

铸态Mg-xSn-1Mn合金的显微组织和阻尼性能

采用光学显微镜(OM)、维氏硬度计、热动态分析仪、X射线衍射(XRD)、多功能内耗仪等,研究了Sn含量对Mg-xSn-1Mn合金显微组织、阻尼性能和力学性能的影响。结果表明:当Sn含量从2%增加到8%时,Mg-xSn-1Mn合金的枝晶间隙呈现细化的趋势,硬度从43.84 HV0.1增加至54.00 HV0.1,呈单调增加的趋势。应变无关阻尼随着Sn含量的增加呈现先增后减的趋势,在Sn含量为4%时达到最大,应变相关阻尼则随着Sn含量的增加呈现逐渐减小的趋势。在低温阶段,相同Sn含量的合金的阻尼随着频率的增大呈现增加的趋势;但在高温下,阻尼值在低频时的上升速率比高频时快,并随着温度的升高,低频阻尼和高频阻尼趋向于相等。当Sn含量不同时,随着温度的升高,Sn含量较高的合金的阻尼值上升速率变快。     

Fabrication,structural and dielectric property of lead-free perovskite silver niobate ceramics

Dielectric capacitors with high recoverable energy density are in high demand for their application in electrical and electronic systems. Among lead-free dielectric materials, silver niobate (AgNbO₃) has attracted growing interest due to its superior energy storage density at room temperature. The field-induced phase transition from antiferroelectric (AFE) phase to ferroelectric (FE) phase contributes to its large energy density. In this work, pure perovskite silver niobate ceramics were fabricated in an oxygen atmosphere by the solid-state reaction technique. The Pbcm orthorhombic phase of AgNbO₃ was closely observed using the Rietveld refinement method to provide explanation for the origin of high spontaneous polarization within a unit cell. Local structural analysis via piezoelectric force microscopy revealed the existence of ferroelectric nano domains, which may contribute to the high energy storage efficiency (η = 99.9926%) in AgNbO₃ at low electric fields. The phase transitions of AgNbO₃ were also investigated via the dependence of the dielectric permittivity (ε′ and ε″) and loss angle tangent (tanδ) on temperatures, providing insights into the further modification of AgNbO₃.     

磁流变阻尼器抑制转子系统振动试验

针对大型旋转机械通过临界转速时振动过大及运行中故障频发等问题,搭建转子试验台,模拟启停机过程和碰摩、不对中故障。不改变原有支撑形式,安装自主设计的磁流变阻尼器,在不停机的情况下,试验研究阻尼器抑制转子通过临界转速时振动过大及各类故障振动。试验结果表明,阻尼器可以有效抑制转子系统临界转速附近的振动,降幅在60%以上;转子发生碰摩或不对中故障时,阻尼器可以降低其高倍频振动。     

Influence of Bridgman solidification on microstructures and magnetic behaviors of a non-equiatomic FeCoNiAlSi high-entropy alloy

The non-equiatomic FeCoNiAlSi alloy is prepared by the Bridgman solidification (BS) technique at different withdrawal velocities (V = 30, 100, and 200 μm/s). Various characterization techniques have been used to study the microstructure and crystal orientation. The morphological evolutions accompanying the crystal growth of the alloy prepared at different withdrawal velocities are nearly the same, from equiaxed grains to columnar crystals. The transition of coercivity is closely related to the local microstructure, while the saturation magnetization changes little at different sites. The coercivity can be significantly reduced from the equiaxed grain area to the columnar crystal area when the applied magnetic field direction is parallel to the crystal growth direction, no matter what is the withdrawal velocity. In addition, the alloy possesses magnetic anisotropy when the applied magnetic field is in different directions.     

Characterization of an acrylic polymer under hygrothermal aging as an optically clear adhesive for touch screen panels

Optically clear adhesives (OCAs) are key components of touch screen panels (TSPs). It is important that OCAs do not affect the transparent electrodes in TSPs because OCAs are contacted to the transparent electrodes. Therefore, N-vinyl caprolactam (NVC) was incorporated in the composition of an acrylic pressure sensitive adhesive (PSA) with excluding an acidic component to maintain the cohesion for OCA preparation. With increasing amounts of NVC, the tack and peel strength of UV-cured PSA increased, but high amounts of NVC led to decreased peel strength. The UV-cured PSA films were placed in a high temperature and humidity chamber for 8 weeks to investigate the durability and corrosion property under hygrothermal conditions. In this study, the corrosion test method using copper foil was suggested as a simple and economical method and was used to evaluate the effect of NVC on the corrosion property of PSA. This method helped identify suitable OCAs that do not have corrosive property. PSA films containing more than 20 wt% of NVC promoted the corrosion of copper foil under hygrothermal aging conditions. The caprolactam ring was opened by moisture, and the PSA structure morphed into a polar structure during the aging process. This change caused a glass transition shift, an increase in the storage modulus at the rubbery plateau, and an increase in peel strength. The surface free energy of the PSA films also increased due to the increase in the polar property. However, high amounts of NVC caused a decrease in the peel strength after 8 weeks of aging because of increased molecular interactions.     

黑色着色剂在湿法涂层中的应用研究

采用含黑色着色剂的涂层浆对尼龙6织物进行湿法涂层,通过测定着色剂在涂层浆中的稳定性及着色剂对涂层织物的着色性和色牢度等性能,研究了黑色着色剂种类、着色剂复配比例及用量、分散剂种类及用量对湿法涂层性能的影响。试验结果表明:炭黑301和中性染料S-RR在湿法涂层中的应用性能较好,并对其进行复配研究,确定中性染料S-RR和炭黑301的复配比例为3∶1,用量为8g;分散剂为TS100,用量为1.0g。